Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Kitchen Remodeling: The Tampa Owner’s Guide
We install and replace Barrette kitchen remodeling components across Tampa, with most full Barrette kitchen remodels here running $14,000 to $45,000 installed. Barrette is a name we see often in Tampa homes, particularly on cabinet hardware, decorative paneling, and trim systems that homeowners bought through big-box retailers. What usually brings someone to this page is a specific failure: a drawer glide that’s come loose inside the cabinet box, a hinge plate pulling away from a particleboard door, a trim piece that’s warped after a few humid Tampa summers. We’ll walk you through what’s fixable, what should be replaced, and exactly what it costs.
Which Barrette Models This Applies To
Barrette’s kitchen remodeling line spans three families we handle regularly in Tampa: the decorative trim and molding series (often sold as paintable PVC or MDF boards), the cabinet hardware and accessory systems (hinges, drawer slides, pull-out trays), and the bath/kitchen wall panel kits. The compatibility gotcha we see most often in older Seminole Heights and Tampa Heights homes is mounting hole spacing: Barrette’s older panel systems use 16-inch stud spacing, but many of the 1920s bungalows we work in have irregular stud bays that were never on any standard spacing. That means a panel that looks right on paper won’t land on two studs without blocking behind it. Before you order anything, pull one panel off and measure the actual distance between your studs, not what the framing was supposed to be. For cabinet hardware, Barrette’s hinge plates generally match the industry 35mm cup bore, but the screw pattern is slightly wider than KraftMaid’s standard, so using KraftMaid hinge plates on Barrette doors leaves an exposed half-moon of the old bore hole.
On the OEM versus aftermarket decision: we stock genuine Barrette replacements where they’re available, and we also carry aftermarket equivalents for Barrette drawer slides and hinge plates that are made in the same Taiwan factories Barrette has used for years. The aftermarket slides are typically $4 to $9 less per pair and carry the same 75-pound rating. For anything structural (panel kits, trim systems), we recommend genuine Barrette because the color match on their white PVC trims is noticeably different from generic white trim after a year of Florida sun.
Styles & brands we work with
Signs Your Barrette Kitchen Remodeling Is Failing
- Drawer drops or catches at the back of the track. The nylon roller inside Barrette’s side-mount slides wears flat on one side, usually on the drawer your kids open with their full body weight. Once the roller isn’t round, the drawer rides down and the rail starts gouging the cabinet floor.
- Hinge plates pulling away from the cabinet frame. Barrette’s MDF and particleboard doors hold hinge screws fine until the bore gets stripped by one too many door slams. You’ll see the door tilt, and the top corner starts rubbing the frame when you close it.
- White trim yellowing or bowing along a sink wall. Tampa humidity gets behind unsealed PVC trim joints, especially behind a kitchen sink where water sits. The PVC itself doesn’t rot, but the adhesive behind it releases, and the trim pulls away from the wall in a slow wave.
- Pull-out tray wobbling side to side. The mounting brackets on Barrette’s accessory trays loosen over three or four years of everyday use. The tray still slides, but the wobble puts strain on the slides and eventually bends the rail enough that the tray jams.
- Soft-close door slamming or not staying closed. Barrette’s soft-close dampers are small, and when the damping fluid leaks out, the door loses its cushion. On a cabinet near the range, heat accelerates that leak.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Tampa, replacing Barrette cabinet hardware (hinges, slides, trays) on a typical 20-door kitchen runs $400 to $1,800 installed, depending on whether we’re swapping just the worn pieces or redoing every door and drawer for consistency. A full Barrette kitchen remodel, including cabinets, countertops, and trim, lands at $14,000 to $45,000, with the range driven by cabinet count, countertop material choice (Cambria and Silestone fall on the higher end of that), and whether we’re moving plumbing or electrical. Every price we quote is written before work starts, parts and labor separated on one line-item sheet. We don’t add change orders if the crew finds something unexpected behind a wall; we call you, we write the new number down, and you approve it before we proceed. The labor on Barrette-specific repairs is covered under our 365-Day Done Right Promise, and genuine Barrette or aftermarket parts carry their own manufacturer’s warranty, which we register for you at install.
DIY or Call Us?
Barrette hardware is generally low-risk to inspect yourself: pull a drawer out, check the roller wheels for flat spots, and tighten any loose hinge screws. What we’d not recommend doing on your own is removing a Barrette panel kit or structural trim run, because the adhesive behind it often tears drywall paper as it comes off, and the fix is a lot more than just gluing it back. Same goes for soft-close dampers inside cabinet hinges: they’re small, spring-loaded, and if you open the hinge body the wrong way the damper launches across the kitchen. Cabinet hardware here doesn’t carry the same injury risk as a high-tension garage spring or an electrical panel, but the damage to a cabinet box from a mis-installed slide is real and not covered by anyone’s warranty. If you’ve got one sticky drawer, try tightening the screws. If half the kitchen is sagging, call (850) 779-4017 and we’ll walk it with you.
FAQs
In Tampa’s humidity, Barrette drawer slides and hinge plates typically last 7 to 10 years before showing real wear, and soft-close dampers often need replacing at the 5 to 7 year mark if the kitchen gets heavy daily use. The trim and panel products hold up longer, 12 to 15 years, but only if the joints were sealed correctly at install. Call (850) 779-4017 if you want us to take a look at what’s wearing and what’s still solid.
No, Barrette slides aren’t built to be rebuilt, and the nylon rollers and ball bearings aren’t sold as separate service parts. Once a slide is scored or the roller has gone flat, the only real fix is a new slide, and we recommend doing the pair on that drawer so both sides wear evenly. We stock Barrette-compatible slides on our trucks, so most swaps happen in one visit.
A full kitchen of Barrette hinge and slide replacement, meaning 20 to 25 doors and drawers, takes our crew four to six hours, including adjusting every door so it closes square. A single cracked hinge plate is a 45 minute stop. You’ll get a written price before we unscrew anything, and the clean-up photo is sent to you before we pull out of the driveway.
We stock the Barrette hinge plates, drawer slides, and pull-out tray brackets that fail most often in Tampa kitchens, along with the aftermarket equivalents where we’ve found the quality matches. For less common Barrette trim profiles and panel kits, we order direct and typically have them in hand within a week. Call (850) 779-4017 and we’ll tell you during that first call whether the part is on the truck or on order.
If your Barrette kitchen components are failing and you want a real price, not a guess, call Elmstead Remodeling Tampa at (850) 779-4017. We’ll schedule a walkthrough, write the number down, and if we replace it, you get our 365-Day Done Right Promise on top of the manufacturer’s warranty. The quote is free, and a live person answers the phone.
Written by Graham Stein, Owner, Elmstead Remodeling Tampa at Elmstead Remodeling Tampa, serving Tampa and nearby areas.
